Calculate Percent Alcohol in Beer

It is easy to calculate percent alcohol in beer and it only requires two important measurements.  A beers alcohol level is measured in Alcohol by Volume (ABV), it is the calculated amount of the total volume of liquid that is alcohol.  The density of a liquid is often measured in unit of specific gravity, where water has an approximate density of 1.00 g/mL or a specific gravity of 1.000 at 60F.  The specific gravity of a liquid is a comparison of its density vs the density of water.

During the fermenting process, yeast is added and the yeast eat the sugars in the wort(sugar water) producing alcohol and CO2.  After fermentation, since alcohol is less dense then wort (sugar water) there will be a change in the specific gravity of the liquid.  ABV is calculated by taking a specific gravity reading of the wort, beer before fermentation, and beer after the fermentation.  The two measurements are referred to as the Original Gravity(wort) and Final Gravity(beer post fermentation).

Measuring Specific Gravity

Measuring the specific gravity is often either done by a hydrometer or a refractometer.   All measurements should be done at what the hydrometer or refractometer is calibrated to, usually 60 °F.

To measure the specific gravity using a hydrometer fill the cylinder until about 2-3 remain of head space, drop in the hydrometer slowly and spin it.  When reading the hydrometer make sure it is not clinging to the side of the cylinder, it should be completely floating.

fill cylinder with 2-3 inch head space

Using a refractometer is much easier and requires only a drop of liquid.  A refractometer measures the density of a liquid in units of brix, amount of sugars present in a liquid.  There is a coversion equation below to go from brix to specific gravity.

refractometer

Equations to Determine ABV

Here is a basic equation that can be used to determine ABV of a beer.  Two contants are used.

1.05 g — represents the amount of CO2 produced for every gram of ethanol produced
0.79 g/mL  — represents the density of ethanol alcohol, drop the g/mL to get the specific gravity.

(  ( 1.05  x  ( OG – FG )  )  / FG  )  / 0.79  x  100 = % ABV

*For temperature correction use the following  ~50 °F subtract .001  /~ 70 ° F add .001 / ~ 80 ° F add .002

For example, lets say you are brewing up a dry irsh stout and your OG=1.052 with your FG=1.014.

(  ( 1.05  x  ( 1.052 – 1.014 )  )  / 1.014  )  / 0.79  x  100 = 4.98% ABV

Here is an equation that can be used to convert units of brix to units of specific gravity.  This is an estimate equation, refer to the USDA Brix Measurements doc for the extact conversion numbers.

Specific Gravity = 1 +(0.004 x °Brix)

5 Responses to “Calculate Percent Alcohol in Beer”
1. rick hoffman says:

How important is the temperature when taking hydrometer readings?
1.05 OG and 1.01 FG
I didn’t record temperatures, but ambient around 70F

2. Jessie says:

I cannot thank you enough for this amazingly helpful post. I’m new to homebrew & am NOT a math genius by any stretch of the imagination. I got a nifty refractometer for a Yule present but every site I’ve seen to try to help me figure out the ABV based off the brix readings give me a whole mess of formulas with the assumption that I know what all the numbers mean.

You’ve broken this down admirably so that a math dunce like me can actually figure it out. Thank you & happy brewing!
~Jessie

3. Roko Peros says:

It’s important if you really want to be accurate. If your OG was 1.05 and your FG 1.01 and they were taken at 70 degrees a slight increase on each reading by about .001 would get you exact. It is more important if you are measuring lets say your OG at 100 degrees, then you would need to add .005 to your measurement.